# generated by PrusaSlicer 2.9.0 on 2025-03-18 at 08:51:44 UTC

[print:0.10mm_DETAIL_ASA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 100
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = adaptivecubic
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.42
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 積層ピッチを細かくすることで高さ方向の解像度を高める設定です。\n造形の所要時間は0.2mmピッチに比べて長くなります。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 3
post_process = 
print_settings_id = 20240610-ASA4-0.10mm STANDARD @G-ZERO L1
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 8
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_DETAIL_PLA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 8000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 150
external_perimeters_first = 1
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 15%
fill_pattern = adaptivecubic
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 1
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 積層ピッチを細かくすることで高さ方向の解像度を高める設定です。\n造形の所要時間は0.2mmピッチに比べて長くなります。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 2
post_process = 
print_settings_id = 20240610_L1_PLA_Tuning.3mf (0.10mm DRAFT @L1)
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 40
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON-FLEX-PA12(NTU62)@G-ZERO_0.2]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotoniclines
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.6
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.05
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.24
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.2
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.22
first_layer_height = 0.1
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0063
gcode_substitutions = 
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.2
infill_first = 0
infill_overlap = 8%
infill_speed = 100
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 2%
ironing_spacing = 0.1
ironing_speed = 40
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 10
max_volumetric_extrusion_rate_slope_positive = 10
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POTICON FLEX PA12 (NTU62)\n\n
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.2
perimeter_generator = arachne
perimeter_speed = 100
perimeters = 4
post_process = 
print_settings_id = 0.10mm_POTICON-FLEX-PA12(NTU62)@G-ZERO_0.2
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 5
skirts = 1
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.22
solid_infill_speed = 120
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.1
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 5
support_material_contact_distance = 0.06
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.2
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 8
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear-grid
support_material_spacing = 1.2
support_material_speed = 100
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 0.22
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 1
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.4
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.16
top_one_perimeter_type = top
top_solid_infill_acceleration = 3000
top_solid_infill_speed = 60
top_solid_layers = 7
top_solid_min_thickness = 0.6
travel_acceleration = 5000
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON-HARD-PPS(RT4)@G-ZERO_0.2]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotoniclines
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.6
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.05
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.24
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.2
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.22
first_layer_height = 0.1
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0063
gcode_substitutions = 
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.2
infill_first = 0
infill_overlap = 8%
infill_speed = 100
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 2%
ironing_spacing = 0.1
ironing_speed = 40
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 10
max_volumetric_extrusion_rate_slope_positive = 10
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POTICON FLEX PA12 (NTU62)\n\n
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.2
perimeter_generator = arachne
perimeter_speed = 100
perimeters = 4
post_process = 
print_settings_id = RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (T_0.005_80-100_infill100_Base_Saito_RT4E)))))))
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 5
skirts = 1
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.22
solid_infill_speed = 120
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.1
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 5
support_material_contact_distance = 0.06
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.18
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 1.2
support_material_speed = 100
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 0.22
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 1
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.4
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.16
top_one_perimeter_type = top
top_solid_infill_acceleration = 3000
top_solid_infill_speed = 60
top_solid_layers = 7
top_solid_min_thickness = 0.6
travel_acceleration = 5000
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON-PA@G-ZERO_0.2]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotoniclines
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.6
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.05
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.24
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.2
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.22
first_layer_height = 0.1
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0063
gcode_substitutions = 
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.2
infill_first = 0
infill_overlap = 8%
infill_speed = 100
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 2%
ironing_spacing = 0.1
ironing_speed = 40
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 10
max_volumetric_extrusion_rate_slope_positive = 10
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POTICON FLEX PA12 (NTU62)\n\n
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.2
perimeter_generator = arachne
perimeter_speed = 100
perimeters = 4
post_process = 
print_settings_id = RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (RT4E.3mf (T_0.005_80-100_infill100_Base_Saito_RT4E)))))))
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 5
skirts = 1
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.22
solid_infill_speed = 120
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.1
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 5
support_material_contact_distance = 0.06
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.18
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 1.2
support_material_speed = 100
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 0.22
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 1
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.4
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.16
top_one_perimeter_type = top
top_solid_infill_acceleration = 3000
top_solid_infill_speed = 60
top_solid_layers = 7
top_solid_min_thickness = 0.6
travel_acceleration = 5000
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 50%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 12
bottom_solid_min_thickness = 1.2
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.38
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.38
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_overlap = 8%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POSICON STD PA1  (NTL34M /34MB)\n-POSICON STD PA1 (NTL36 /36B)\n-POTICON FLEX PA12 (NTU62)\n-POTICON HARD PPS (RT4)\n-POTICON ESD PPS (RT4E)\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 3
post_process = 
print_settings_id = 0.10mm QUALITY @G-ZERO
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.38
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.08
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 35%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 60
top_solid_layers = 12
top_solid_min_thickness = 1.2
travel_acceleration = 5000
travel_speed = 500
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.02

[print:0.10mm_POTICON_ESD-PPS(RT4E)@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 50%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 8
bottom_solid_min_thickness = 0.6
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_separation = 0.1
brim_type = outer_only
brim_width = 6
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.38
external_perimeter_speed = 120
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.38
fill_angle = 45
fill_density = 30%
fill_pattern = adaptivecubic
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 100
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 20000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.44
infill_first = 0
infill_overlap = 8%
infill_speed = 250
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 400
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POSICON STD PA1  (NTL34M /34MB)\n-POSICON STD PA1 (NTL36 /36B)\n-POTICON FLEX PA12 (NTU62)\n-POTICON HARD PPS (RT4)\n-POTICON ESD PPS (RT4E)\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 20
overhang_speed_1 = 40
overhang_speed_2 = 60
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 2
post_process = 
print_settings_id = 0.10mm QUALITY @G-ZERO
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 120
solid_infill_acceleration = 20000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.38
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.08
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.04
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 100
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 35%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 7500
top_solid_infill_speed = 120
top_solid_layers = 8
top_solid_min_thickness = 0.6
travel_acceleration = 5000
travel_speed = 500
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON_ESD-PPS(RT4E)@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 50%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 8
bottom_solid_min_thickness = 0.6
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_separation = 0.1
brim_type = outer_only
brim_width = 6
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.38
external_perimeter_speed = 120
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.38
fill_angle = 45
fill_density = 30%
fill_pattern = adaptivecubic
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 100
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 20000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.44
infill_first = 0
infill_overlap = 8%
infill_speed = 250
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 400
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POSICON STD PA1  (NTL34M /34MB)\n-POSICON STD PA1 (NTL36 /36B)\n-POTICON FLEX PA12 (NTU62)\n-POTICON HARD PPS (RT4)\n-POTICON ESD PPS (RT4E)\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 20
overhang_speed_1 = 40
overhang_speed_2 = 60
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 2
post_process = 
print_settings_id = 0.10mm QUALITY @G-ZERO
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 120
solid_infill_acceleration = 20000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.38
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.08
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.04
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 100
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 35%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 7500
top_solid_infill_speed = 120
top_solid_layers = 8
top_solid_min_thickness = 0.6
travel_acceleration = 5000
travel_speed = 500
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON_FLEX-PA12@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 6
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 4000
external_perimeter_extrusion_width = 0.5
external_perimeter_speed = 100
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.36
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 100
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.42
infill_first = 0
infill_overlap = 10%
infill_speed = 250
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 20
max_volumetric_extrusion_rate_slope_positive = 20
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 積層ピッチを細かくすることで高さ方向の解像度を高める設定です。\n造形の所要時間は0.2mmピッチに比べて長くなります。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 40
overhangs = 1
perimeter_acceleration = 5000
perimeter_extruder = 1
perimeter_extrusion_width = 0.36
perimeter_generator = arachne
perimeter_speed = 120
perimeters = 3
post_process = 
print_settings_id = NTU_0.10mm QUALITY @G-ZERO_L1_0.4mm
raft_contact_distance = 0.05
raft_expansion = 5
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 3
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 40
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.36
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.16
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.45
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.3
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 0.4
support_material_speed = 200
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 6
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON_HARD-PPS(RT4)@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 1000
bottom_fill_pattern = monotonic
bottom_solid_layers = 8
bottom_solid_min_thickness = 0.8
bridge_acceleration = 5000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_separation = 0.25
brim_type = outer_only
brim_width = 4
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 20000
dont_support_bridges = 0
draft_shield = limited
elefant_foot_compensation = 0.05
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.41
external_perimeter_speed = 60
external_perimeters_first = 1
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.4
fill_angle = 45
fill_density = 30%
fill_pattern = triangles
first_layer_acceleration = 5000
first_layer_acceleration_over_raft = 14998
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 100
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 20000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.38
infill_first = 1
infill_overlap = 20%
infill_speed = 150
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 2%
ironing_spacing = 0.1
ironing_speed = 100
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 200
max_volumetric_extrusion_rate_slope_positive = 200
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 積層ピッチを細かくすることで高さ方向の解像度を高める設定です。\n造形の所要時間は0.2mmピッチに比べて長くなります。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 50
overhangs = 1
perimeter_acceleration = 20000
perimeter_extruder = 1
perimeter_extrusion_width = 0.32
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 4
post_process = 
print_settings_id = L1_RT4E_Layer0.1mm__20240612
raft_contact_distance = 0
raft_expansion = 4
raft_first_layer_density = 80%
raft_first_layer_expansion = 1.6
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 4
skirt_height = 4
skirts = 3
slice_closing_radius = 0.001
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 20000
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.36
solid_infill_speed = 150
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 4
support_material_contact_distance = 0.05
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.3
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.05
support_material_interface_speed = 45
support_material_pattern = rectilinear
support_material_spacing = 0.4
support_material_speed = 100
support_material_style = snug
support_material_synchronize_layers = 1
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 120%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 8
top_solid_min_thickness = 0.8
travel_acceleration = 20000
travel_speed = 450
travel_speed_z = 20
wall_distribution_count = 1
wall_transition_angle = 5
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_POTICON_PA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 5
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.5
external_perimeter_speed = 120
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = adaptivecubic
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.42
infill_first = 0
infill_overlap = 10%
infill_speed = 200
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 積層ピッチを細かくすることで高さ方向の解像度を高める設定です。\n造形の所要時間は0.2mmピッチに比べて長くなります。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 160
perimeters = 3
post_process = 
print_settings_id = L1_NTL34M-36_Layer0.1mm
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 30
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 50
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 120
top_solid_layers = 8
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.10mm_QUALITY@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 50%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 10
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 6
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.44
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.42
infill_first = 0
infill_overlap = 5%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形品質を優先する設定です。\n積層を目立たせたくない場合におすすめの設定です。\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 3
post_process = 
print_settings_id = 0.10mm QUALITY @G-ZERO
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.08
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 90%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 35%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 60
top_solid_layers = 10
top_solid_min_thickness = 1
travel_acceleration = 5000
travel_speed = 450
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.03

[print:0.10mm_TYPICAL@G-ZERO_0.2]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotoniclines
bottom_solid_layers = 8
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.05
brim_type = no_brim
brim_width = 5
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.05
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.24
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.2
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.24
first_layer_height = 0.1
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 40
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0063
gcode_substitutions = 
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.2
infill_first = 0
infill_overlap = 8%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 2%
ironing_spacing = 0.1
ironing_speed = 40
ironing_type = top
layer_height = 0.1
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 10
max_volumetric_extrusion_rate_slope_positive = 10
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 0.2mmノズル用設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.2
perimeter_generator = arachne
perimeter_speed = 60
perimeters = 4
post_process = 
print_settings_id = 0.10mm_TYPICAL @G-ZERO_N0.2
raft_contact_distance = 0.04
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 3
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 3
skirts = 3
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 40
solid_infill_acceleration = 15000
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.2
solid_infill_speed = 60
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.1
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 5
support_material_contact_distance = 0.06
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.18
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.02
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 100
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_with_sheath = 0
support_material_xy_spacing = 0.2
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 1
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.4
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.16
top_one_perimeter_type = top
top_solid_infill_acceleration = 3000
top_solid_infill_speed = 40
top_solid_layers = 8
top_solid_min_thickness = 0.8
travel_acceleration = 5000
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.02

[print:0.20mm_DRAFT_ASA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 8000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 150
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 15%
fill_pattern = adaptivecubic
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 50
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形時間の短縮を重視する設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 25
overhang_speed_1 = 25
overhang_speed_2 = 30
overhang_speed_3 = 40
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 2
post_process = 
print_settings_id = ASA-0.20mm DRAFT @G-ZERO L1
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.16
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = top
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_DRAFT_PLA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 8000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 150
external_perimeters_first = 1
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 15%
fill_pattern = adaptivecubic
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 1
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形時間の短縮を重視する設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 40
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 2
post_process = 
print_settings_id = 20240603_L1_PLA_Tuning.3mf (0.20mm DRAFT @L1)
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 40
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_PA-CF@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 6
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1.05
bridge_speed = 40
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 7500
external_perimeter_extrusion_width = 0.44
external_perimeter_speed = 100
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 25%
fill_pattern = adaptivecubic
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.46
first_layer_height = 0.2
first_layer_speed = 100
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 100
gcode_comments = 0
gcode_label_objects = octoprint
gcode_resolution = 0.00625
gcode_substitutions = "G1 F0";"\\n";;
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.44
infill_first = 0
infill_overlap = 40%
infill_speed = 220
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 50
max_volumetric_extrusion_rate_slope_positive = 50
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 60%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 美しくはっきりとした積層跡を重視(外周300mm/s,8k)\n-ゴースティングを十分に抑制する
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode
overhang_speed_0 = 25
overhang_speed_1 = 40
overhang_speed_2 = 50
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 15000
perimeter_extruder = 1
perimeter_extrusion_width = 0.36
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 3
post_process = 
print_settings_id = G0_PA12CF_Tentative_2502_V0.3mf (G0_PA12CF_Tentative_2502_V0.3mf (G0_PA12CF_Tentative_2502_V0.3mf (L1_PA12CF_Tentative_20241125.3mf (L1_PA12CF_Tentative_20241125.3mf (dipus_PA6CF_Tentative_20241122.3mf (dipus_PA6CF_Tentative_20241122.3mf (Arm3_PA6CF_Tentative_20240805.3mf (Arm3_PA6CF_Tentative_20240805.3mf (L1_PA6CF_Tentative_20240805.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V2.3mf (NOK_PA6CF_V2.3mf (NOK_PA6CF_V1.3mf (NOK_PA6CF_V0.3mf (PA6_L1_V2.3mf (0.20mm PA6-CF TYPICAL @L1))))))))))))))))))))
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 0.8
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = random
single_extruder_multi_material_priming = 0
skirt_distance = 0.4
skirt_height = 1
skirts = 8
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 100
solid_infill_acceleration = 15000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.08
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.34
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 120
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 220
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.36
top_one_perimeter_type = top
top_solid_infill_acceleration = 7500
top_solid_infill_speed = 100
top_solid_layers = 6
top_solid_min_thickness = 1
travel_acceleration = 7500
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_POTICON-FLEX-PA12@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 65
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.45
first_layer_height = 0.2
first_layer_speed = 65
first_layer_speed_over_raft = 65
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 65
gcode_comments = 0
gcode_label_objects = octoprint
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 20000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 1
infill_overlap = 20%
infill_speed = 200
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 45
max_volumetric_extrusion_rate_slope_positive = 45
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POSICON STD PA1  (NTL34M /34MB)\n-POSICON STD PA1 (NTL36 /36B)\n-POTICON FLEX PA12 (NTU62)\n-POTICON HARD PPS (RT4)\n-POTICON ESD PPS (RT4E)\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 135
perimeters = 2
post_process = 
print_settings_id = 0.20mm TYPICAL @G-ZERO
raft_contact_distance = 0.08
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 65
solid_infill_acceleration = 10000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 150
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.08
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.06
support_material_interface_speed = 60
support_material_pattern = rectilinear-grid
support_material_spacing = 2.5
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 35
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 6
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 65
top_solid_layers = 4
top_solid_min_thickness = 0.8
travel_acceleration = 7500
travel_speed = 450
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 3000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.03

[print:0.20mm_POTICON@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 6
bottom_solid_min_thickness = 1.2
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 6
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 65
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_overlap = 10%
infill_speed = 200
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = For\n-POSICON STD PA1  (NTL34M /34MB)\n-POSICON STD PA1 (NTL36 /36B)\n-POTICON FLEX PA12 (NTU62)\n-POTICON HARD PPS (RT4)\n-POTICON ESD PPS (RT4E)\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 35
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 135
perimeters = 3
post_process = 
print_settings_id = 0.20mm TYPICAL @G-ZERO
raft_contact_distance = 0.08
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 150
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.08
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 100%
support_tree_angle = 35
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 6
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 65
top_solid_layers = 6
top_solid_min_thickness = 1.2
travel_acceleration = 5000
travel_speed = 500
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.03

[print:0.20mm_POTICON_FLEX-PA12(NTU62)@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 10000
bridge_angle = 0
bridge_flow_ratio = 0.9
bridge_speed = 60
brim_separation = 0.3
brim_type = outer_only
brim_width = 4
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 15000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 4000
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 120
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 23
extruder_clearance_radius = 65
extrusion_width = 0.4
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 2000
first_layer_acceleration_over_raft = 400
first_layer_extrusion_width = 0.46
first_layer_height = 0.2
first_layer_speed = 50
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 100
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00625
gcode_substitutions = "G1 F0\\n";;;"G1 F0エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.37
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 20
max_volumetric_extrusion_rate_slope_positive = 20
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形時間の短縮を重視する設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 50
overhangs = 1
perimeter_acceleration = 8000
perimeter_extruder = 1
perimeter_extrusion_width = 0.38
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 3
post_process = 
print_settings_id = L1_NTU62_Layer0.20
raft_contact_distance = 0.03
raft_expansion = 5
raft_first_layer_density = 95%
raft_first_layer_expansion = 0.4
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 0
skirt_height = 1
skirts = 6
slice_closing_radius = 0.01
slicing_mode = regular
small_perimeter_speed = 120
solid_infill_acceleration = 15000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.37
solid_infill_speed = 300
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.125
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = auto
support_material_interface_spacing = 0.1
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 0.4
support_material_speed = 300
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 0.25
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.38
top_one_perimeter_type = none
top_solid_infill_acceleration = 8000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.8
travel_acceleration = 20000
travel_speed = 400
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.02

[print:0.20mm_POTICON_PA@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 8000
external_perimeter_extrusion_width = 0.42
external_perimeter_speed = 150
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 15%
fill_pattern = adaptivecubic
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 100
max_volumetric_extrusion_rate_slope_positive = 100
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形時間の短縮を重視する設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 25
overhang_speed_1 = 25
overhang_speed_2 = 30
overhang_speed_3 = 40
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 2
post_process = 
print_settings_id = 20240604_Astronaut_Phil_A_Ment_0.2mm_PA(34MB)_G-ZERO_1h36m.gcode (0.20mm DRAFT @G-ZERO L1)
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_TPU@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = no_brim
brim_width = 6
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.46
external_perimeter_speed = 60
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.46
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 20000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.48
infill_first = 0
infill_overlap = 15%
infill_speed = 120
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 20
max_volumetric_extrusion_rate_slope_positive = 20
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 軟質フィラメントを造形する際の設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 20
overhang_speed_1 = 30
overhang_speed_2 = 40
overhang_speed_3 = 50
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 120
perimeters = 3
post_process = 
print_settings_id = 0.20mm FLEX @G-ZERO
raft_contact_distance = 0.08
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 120
spiral_vase = 0
staggered_inner_seams = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.16
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.24
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.06
support_material_interface_speed = 40
support_material_pattern = rectilinear-grid
support_material_spacing = 2.5
support_material_speed = 100
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 100%
support_tree_angle = 35
support_tree_angle_slow = 20
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 15000
travel_speed = 400
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_TPU@G-ZERO_L1_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.8
bridge_acceleration = 500
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 15
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.15
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 8000
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 150
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 3000
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 500
max_volumetric_extrusion_rate_slope_negative = 20
max_volumetric_extrusion_rate_slope_positive = 20
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 造形時間の短縮を重視する設定です。
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Z{layer_height}_{filament_type[0]}_{print_time}_L1_04Nozzle.gcode
overhang_speed_0 = 15
overhang_speed_1 = 20
overhang_speed_2 = 25
overhang_speed_3 = 50
overhangs = 1
perimeter_acceleration = 10000
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 2
post_process = 
print_settings_id = TPU95HF_0.20mm@G-ZERO_L1
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.15
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 1
support_material_interface_extruder = 0
support_material_interface_layers = 4
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 10000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.9
travel_acceleration = 15000
travel_speed = 300
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.20mm_TYPICAL@G-ZERO_0.4]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 100
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 10000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.46
external_perimeter_speed = 100
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 1
extruder_clearance_height = 25
extruder_clearance_radius = 65
extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 400
first_layer_acceleration_over_raft = 200
first_layer_extrusion_width = 0.44
first_layer_height = 0.2
first_layer_speed = 60
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.00442
gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避"
infill_acceleration = 15000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.44
infill_first = 0
infill_overlap = 8%
infill_speed = 200
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 250
max_volumetric_extrusion_rate_slope_negative = 40
max_volumetric_extrusion_rate_slope_positive = 40
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 10
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 印刷時間を重視する場合や、\n積層を強調したい場合におすすめの設定です。\n※強度を高めたい場合は [レイヤーと外周 > 外周設定 > 境界線] を増やしてください。\n※強度を高めたい場合は[インフィル > インフィル >充填密度] を増やしてください
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}_{timestamp}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 40
overhang_speed_3 = 75%
overhangs = 1
perimeter_acceleration = 7500
perimeter_extruder = 1
perimeter_extrusion_width = 0.42
perimeter_generator = arachne
perimeter_speed = 150
perimeters = 3
post_process = 
print_settings_id = BETA_0.20mm TYPICAL @G-ZERO
raft_contact_distance = 0.08
raft_expansion = 3
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
slice_closing_radius = 0.02
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 15000
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.42
solid_infill_speed = 150
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_auto = 1
support_material_bottom_contact_distance = 0.16
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.12
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.04
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 200
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 0
support_material_xy_spacing = 90%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 35%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.32
top_one_perimeter_type = top
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 5000
travel_speed = 450
travel_speed_z = 4
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 5000
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = -0.03

[filament:POTICON_ESD-PPS(RT4E)@G-ZERO_0.4]
bed_temperature = 120
bridge_fan_speed = 40
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_ESD-PPS(RT4E)@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #9696A0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.52
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n本RT4Eグレードはカーボンブラックを配合しておりESDセーフです。\n高い剛性と耐熱性、耐摩耗性、耐薬品性にも優れた素材です。\n\n造形が反ったりする場合は、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n強度が出ない場合にはベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n\n※造形にはテクスチャPEIプレートをご使用ください。\n　特に造形物の底面積が大きい場合は反りや剥がれが発生する場合があります。\n※造形物を複数同時に印刷するのは避けてください。\n　反りや剥がれ、強度低下の原因となる場合があります。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 0.05
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PPS RT4E@G-ZERO"
filament_shrinkage_compensation_xy = 0.3%
filament_shrinkage_compensation_z = 0.15%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = RT4E
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 110
first_layer_temperature = 345
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 50
min_fan_speed = 35
min_print_speed = 15
overhang_fan_speed_0 = 80
overhang_fan_speed_1 = 70
overhang_fan_speed_2 = 60
overhang_fan_speed_3 = 50
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.02\nSET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 345

[filament:POTICON_ESD-PPS(RT4E)@G-ZERO_L1_0.4]
bed_temperature = 120
bridge_fan_speed = 40
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_ESD-PPS(RT4E)@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #9696A0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.52
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n本RT4Eグレードはカーボンブラックを配合しておりESDセーフです。\n高い剛性と耐熱性、耐摩耗性、耐薬品性にも優れた素材です。\n\n造形が反ったりする場合は、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n強度が出ない場合にはベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n\n※造形にはテクスチャPEIプレートをご使用ください。\n　特に造形物の底面積が大きい場合は反りや剥がれが発生する場合があります。\n※造形物を複数同時に印刷するのは避けてください。\n　反りや剥がれ、強度低下の原因となる場合があります。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 0.05
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PPS RT4E@G-ZERO"
filament_shrinkage_compensation_xy = 0.3%
filament_shrinkage_compensation_z = 0.15%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = RT4E
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 110
first_layer_temperature = 345
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 15
overhang_fan_speed_0 = 80
overhang_fan_speed_1 = 70
overhang_fan_speed_2 = 60
overhang_fan_speed_3 = 50
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.02\n"
temperature = 345

[filament:POTICON_FLEX-PA12(NTU62)@G-ZERO_0.2]
bed_temperature = 95
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-FLEX-PA12(NTU62)@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 250
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.08
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 2
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。\n\n※スムースPEIビルドプレートにケープを厚めに吹きかけて定着を確保してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL36@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTU62
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 110
first_layer_temperature = 290
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 75
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 25
start_filament_gcode = "; Filament Start Gcode\nM900 K0.1\n\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_FLEX-PA12(NTU62)@G-ZERO_0.4]
bed_temperature = 105
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_FLEX-PA12@G-ZERO_L1_0.4;0.20mm_POTICON-FLEX-PA12@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.08
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。\n\n※スムースPEIビルドプレートにケープを厚めに吹きかけて定着を確保してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.8
filament_retract_length_toolchange = nil
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL36@G-ZERO"
filament_shrinkage_compensation_xy = 0.5%
filament_shrinkage_compensation_z = 1%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTU62
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 110
first_layer_temperature = 290
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 70
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.065\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1\n"
temperature = 280

[filament:POTICON_FLEX-PA12(NTU62)@G-ZERO_L1_0.4]
bed_temperature = 105
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_FLEX-PA12@G-ZERO_L1_0.4;0.20mm_POTICON_FLEX-PA12(NTU62)@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.08
filament_deretract_speed = 60
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。\n\n※スムースPEIビルドプレートにケープを厚めに吹きかけて定着を確保してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.6
filament_retract_length_toolchange = nil
filament_retract_lift = 0.15
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 60
filament_seam_gap_distance = nil
filament_settings_id = Tuning_NTU62_Nozzle04@G-ZERO_L1
filament_shrinkage_compensation_xy = 0.5%
filament_shrinkage_compensation_z = 1%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTU62
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = 0
first_layer_bed_temperature = 110
first_layer_temperature = 290
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 20
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.03\nSET_FAN_SPEED FAN=chamber_fan SPEED=0"
temperature = 280

[filament:POTICON_HARD-PPS(RT4)@G-ZERO_0.2]
bed_temperature = 90
bridge_fan_speed = 90
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-HARD-PPS(RT4)@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.51
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.5
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n非常に高い剛性と強度、耐熱性、耐摩耗性、耐薬品性にも優れた素材です。\n\n\n造形が反ったりする場合はベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n強度が出ない場合にはベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.1
filament_retract_length_toolchange = nil
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PPS RT4@G-ZERO"
filament_shrinkage_compensation_xy = 0.2%
filament_shrinkage_compensation_z = 0.1%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = RT4
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 85
first_layer_temperature = 340
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.1\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1\n;SET_TEMPERATURE_FAN_TARGET temperature_fan=Chamber_Intake_Fan target=65\n"
temperature = 315

[filament:POTICON_HARD-PPS(RT4)@G-ZERO_0.4]
bed_temperature = 90
bridge_fan_speed = 90
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON@G-ZERO_0.4;0.20mm_POTICON@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.51
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n非常に高い剛性と強度、耐熱性、耐摩耗性、耐薬品性にも優れた素材です。\n\n造形が反ったりする場合はベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n強度が出ない場合にはベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = -50%
filament_settings_id = "Otsuka Chemical POTICON PPS RT4@G-ZERO"
filament_shrinkage_compensation_xy = 0.3%
filament_shrinkage_compensation_z = 0.25%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = RT4
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 85
first_layer_temperature = 340
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.025 \n;SET_FAN_SPEED FAN=chamber_fan SPEED=1\n\n"
temperature = 320

[filament:POTICON_HARD-PPS(RT4)@G-ZERO_L1_0.4]
bed_temperature = 120
bridge_fan_speed = 90
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_HARD-PPS(RT4)@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 100000
filament_density = 1.51
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n非常に高い剛性と強度、耐熱性、耐摩耗性、耐薬品性にも優れた素材です。\n\n造形が反ったりする場合はベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。\n強度が出ない場合にはベッド温度を10～20度上げる、ファン速度を下げる、広めのブリムやドラフトシールドを使用するなどしてください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = -50%
filament_settings_id = L1_RT4E_Layer0.1mm__20240612
filament_shrinkage_compensation_xy = 0.3%
filament_shrinkage_compensation_z = 0.25%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = RT4
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 85
first_layer_temperature = 340
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.025 \n;SET_FAN_SPEED FAN=chamber_fan SPEED=1\n\n"
temperature = 320

[filament:POTICON_STD1-PA(NTL34M)@G-ZERO_0.2]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-PA@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 300
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.5
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34M
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 95
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 30
start_filament_gcode = "; Filament Start Gcode\nM900 K0.1\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD1-PA(NTL34M)@G-ZERO_0.4]
bed_temperature = 47
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON@G-ZERO_0.4;0.20mm_POTICON@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.97
fan_always_on = 1
fan_below_layer_time = 450
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = -25%
filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO"
filament_shrinkage_compensation_xy = 0.16%
filament_shrinkage_compensation_z = 0.4%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34M
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 50
first_layer_temperature = 285
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 45
start_filament_gcode = "; Filament Start Gcode\nM900 K0.025\n"
temperature = 270

[filament:POTICON_STD1-PA(NTL34M)@G-ZERO_L1_0.4]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_PA@G-ZERO_L1_0.4;0.20mm_POTICON_PA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 45
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = -25%
filament_settings_id = "Otsuka Chemical POTICON PA NTL34MB@G-ZERO"
filament_shrinkage_compensation_xy = 0.16%
filament_shrinkage_compensation_z = 0.4%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34M
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 75
min_fan_speed = 50
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 80
overhang_fan_speed_3 = 80
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament Start Gcode\nM900 K0.025\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD1-PA(NTL34MB)@G-ZERO_0.2]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-PA@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.99
fan_always_on = 1
fan_below_layer_time = 300
filament_abrasive = 0
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.5
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34MB
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 30
start_filament_gcode = "; Filament Start Gcode\nM900 K0.1\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD1-PA(NTL34MB)@G-ZERO_0.4]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON@G-ZERO_0.4;0.20mm_POTICON@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.97
fan_always_on = 1
fan_below_layer_time = 300
filament_abrasive = 0
filament_colour = #9696A0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = -25%
filament_settings_id = "Otsuka Chemical POTICON PA NTL34MB@G-ZERO"
filament_shrinkage_compensation_xy = 0.08%
filament_shrinkage_compensation_z = 0.32%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34MB
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 70
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 30
start_filament_gcode = "; Filament Start Gcode\nM900 K0.022\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD1-PA(NTL34MB)@G-ZERO_L1_0.4]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_PA@G-ZERO_L1_0.4;0.20mm_POTICON_PA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 45
filament_abrasive = 0
filament_colour = #9696A0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = -25%
filament_settings_id = "Otsuka Chemical POTICON PA NTL34MB@G-ZERO"
filament_shrinkage_compensation_xy = 0.16%
filament_shrinkage_compensation_z = 0.4%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL34MB
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 75
min_fan_speed = 50
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 80
overhang_fan_speed_3 = 80
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament Start Gcode\nM900 K0.025\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD2-PA(NTL36)@G-ZERO_0.2]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-PA@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.99
fan_always_on = 1
fan_below_layer_time = 200
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.5
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 95
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.1\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD2-PA(NTL36)@G-ZERO_0.4]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON@G-ZERO_0.4;0.20mm_POTICON@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 80
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL36@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0.2%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD2-PA(NTL36)@G-ZERO_L1_0.4]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_PA@G-ZERO_L1_0.4;0.20mm_POTICON_PA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.97
fan_always_on = 1
fan_below_layer_time = 45
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "POTICON STD2 PA (NTL36)@G-ZERO_L1"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0.2%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 75
min_fan_speed = 50
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 80
overhang_fan_speed_3 = 80
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n"
temperature = 270

[filament:POTICON_STD2-PA(NTL36B)@G-ZERO_0.2]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON-PA@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.99
fan_always_on = 1
fan_below_layer_time = 200
filament_abrasive = 0
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.5
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36B
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 95
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.1\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD2-PA(NTL36B)@G-ZERO_0.4]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON@G-ZERO_0.4;0.20mm_POTICON@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 80
filament_abrasive = 0
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 200
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Otsuka Chemical POTICON PA NTL36@G-ZERO"
filament_shrinkage_compensation_xy = 0.02%
filament_shrinkage_compensation_z = 0.1%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36B
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 270

[filament:POTICON_STD2-PA(NTL36B)@G-ZERO_L1_0.4]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_POTICON_PA@G-ZERO_L1_0.4;0.20mm_POTICON_PA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.97
fan_always_on = 1
fan_below_layer_time = 80
filament_abrasive = 0
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 80000
filament_density = 1.4
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。\n造形前に吐出試験(270℃ 2mm/sで50mm押し出し)を行い、\nノズルから吐出されたフィラメントが荒れていないことを確認してください。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "POTICON STD2 PA (NTL36)@G-ZERO_L1"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0.2%
filament_soluble = 0
filament_spool_weight = 305
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = NTL36B
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 75
min_fan_speed = 50
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n"
temperature = 270

[filament:PolyLite_PETG@G-ZERO_0.4]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.20mm_TYPICAL@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 80
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "機械的特性のバランスが良いPETG(グリコール変性PET)樹脂です。\n押し出し体積速度は低めで、高速造形にはやや不向きです。\n\n※ノズルが詰まる場合がありますので印刷する際は上蓋を開けることを推奨します。\n※ビルドプレートについてはスムースPEIを使用すると造形物が剥がれない場合があります。\n　テクスチャビルドプレートを使用してください。\n　どうしてもスムースPEIを使用する場合はPVA糊を塗るなどして剥がしやすくして使用するのをお勧めします。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.3
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker PolyLite PETG@G-ZERO"
filament_shrinkage_compensation_xy = 0.6%
filament_shrinkage_compensation_z = 0.25%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PETG
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = 1
first_layer_bed_temperature = 78
first_layer_temperature = 250
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.015\nSET_FAN_SPEED FAN=chamber_fan SPEED=0"
temperature = 240

[filament:PolyLite_PLA@G-ZERO_0.4]
bed_temperature = 45
bridge_fan_speed = 90
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.20mm_TYPICAL@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.94
fan_always_on = 1
fan_below_layer_time = 300
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "硬く、機械的強度に優れるPLA樹脂です。\n耐熱性は低く(50℃程度)ですので使用と造形に注意が必要です。\n\n※ノズルが詰まる場合がありますので印刷する際は上蓋を開けることを推奨します。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker Polylite PLA@G-ZERO"
filament_shrinkage_compensation_xy = 0.84%
filament_shrinkage_compensation_z = 0.28%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 235
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 80
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 30
start_filament_gcode = "; Filament Start Gcode\nM900 K0.022\nSET_FAN_SPEED FAN=chamber_fan SPEED=0"
temperature = 210

[filament:PolyLite_PLA@G-ZERO_L1_0.4]
bed_temperature = 45
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_DETAIL_PLA@G-ZERO_L1_0.4;0.20mm_DRAFT_PLA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.94
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "硬く、機械的強度に優れるPLA樹脂です。\n耐熱性は低く(50℃程度)ですので使用と造形に注意が必要です。\n\n※ノズルが詰まる場合がありますので印刷する際は上蓋を開けることを推奨します。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "20240604_Polymaker PolyLite PLA@G-ZERO L1"
filament_shrinkage_compensation_xy = 0.84%
filament_shrinkage_compensation_z = 0.28%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 45
first_layer_temperature = 235
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament Start Gcode\nM900 K0.03\nSET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 215

[filament:PolyMide_PA12-CF@G-ZERO_0.4]
bed_temperature = 50
bridge_fan_speed = 75
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO 0.40mm Nozzle";"G-ZERO 0.60mm Nozzle"
compatible_printers_condition = 
compatible_prints = "0.20mm TYPICAL @G-ZERO_N0.4"
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 30
filament_abrasive = 1
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 0
filament_density = 1.04
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "曲げ剛性、強度、特性バランスにすぐれた Polymid PA12-CF です。\n\nTips\n※炭素繊維による摩耗が著しいため、専用のノズルとホットエンドを使用してください。\n※含有する繊維が長いため、0.2㎜以上のレイヤー厚みで印刷してください\n※反りが強い場合は、のりなどの定着補助剤を使用したり、ベッド温度を低くする、風量を調整することでことで改善する場合があります。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.4
filament_retract_length_toolchange = nil
filament_retract_lift = 0
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker PA6-CF@G-ZERO"
filament_shrinkage_compensation_xy = 0.15%
filament_shrinkage_compensation_z = 0.6%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 55
first_layer_temperature = 300
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 75
min_fan_speed = 40
min_print_speed = 25
overhang_fan_speed_0 = 75
overhang_fan_speed_1 = 75
overhang_fan_speed_2 = 75
overhang_fan_speed_3 = 60
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament Start Gcode\nM900 K0.015\nSET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 300

[filament:Polylite_ASA@G-ZERO_0.2]
bed_temperature = 95
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.2mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_TYPICAL@G-ZERO_0.2
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.02
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.2
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.2
filament_retract_length_toolchange = nil
filament_retract_lift = 0.05
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker ASA @G-ZERO_N0.2"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Otsuka Chemical
filament_wipe = nil
first_layer_bed_temperature = 102
first_layer_temperature = 265
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 60
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 90
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.04\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1\n\n"
temperature = 240

[filament:Polylite_ASA@G-ZERO_0.4]
bed_temperature = 95
bridge_fan_speed = 80
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.10mm_QUALITY@G-ZERO_0.4;0.20mm_TYPICAL@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 300
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.04
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 150
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "印刷性、汎用性に優れたASAです。\n-ABSのブタジエンゴムをアクリルゴムに変更した樹脂です。対候性や耐酸、耐アルカリ性にも優れます。\n-野外での使用にお勧め\n-収縮は一般的にABSよりやや穏やかです。\n\n※ASA/ABSの印刷の際にはフロントドアおよびトップリッドを閉めてください。\n※一層目を観察し、ベッドとノズルの距離を適切に調節してください。反り、剥がれの原因になります。\n※印刷物が反る場合はベッド温度を上げて調整してください。\n※反りが強い場合などにはチャンバーファンを使用し、チャンバー温度を上昇させることができます。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker PolyLite ASA@G-ZERO"
filament_shrinkage_compensation_xy = 0.45%
filament_shrinkage_compensation_z = 0.4%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 102
first_layer_temperature = 275
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 70
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament Start Gcode\nM900 K0.022\nSET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 250

[filament:Polylite_ASA@G-ZERO_L1_0.4]
bed_temperature = 100
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.10mm_DETAIL_ASA@G-ZERO_L1_0.4;0.20mm_DRAFT_ASA@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 4800
filament_density = 1.04
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "PolyLite ASA\nPolymaker製のASAです。\nABSと比べて対候性に優れるため、屋外での使用も可能です。\n\n対応ノズル： 0.2mm以上\n積層ピッチ：0.1mm以上\n\n※収縮が強い樹脂であるため、造形物の反り等の問題が発生する場合があります。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "20240614_Polymaker PolyLite ASA@G-ZERO L1"
filament_shrinkage_compensation_xy = 0.45%
filament_shrinkage_compensation_z = 0.4%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 100
first_layer_temperature = 260
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 75
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 90
overhang_fan_speed_3 = 80
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament Start Gcode\nM900 K0.015\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0"
temperature = 245

[filament:Polylite_PC@G-ZERO_0.4]
bed_temperature = 110
bridge_fan_speed = 90
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.20mm_TYPICAL@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.94
fan_always_on = 1
fan_below_layer_time = 60
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 6000
filament_density = 1.19
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "扱いやすいポリカーボネート材料です。\n押し出し体積速度は低めで、高速造形にはやや不向きです。\n\n※ビルドプレートについてはスムースPEIを使用すると造形物が剥がれない場合があります。\n　テクスチャビルドプレートを使用してください。\n　どうしてもスムースPEIを使用する場合はPVA糊を塗るなどして剥がしやすくして使用するのをお勧めします。"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.3
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker Polylite PC@G-ZERO"
filament_shrinkage_compensation_xy = 0.58%
filament_shrinkage_compensation_z = 0.34%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PC
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 105
first_layer_temperature = 290
full_fan_speed_layer = 4
idle_temperature = nil
inherits = 
max_fan_speed = 95
min_fan_speed = 50
min_print_speed = 20
overhang_fan_speed_0 = 84
overhang_fan_speed_1 = 80
overhang_fan_speed_2 = 70
overhang_fan_speed_3 = 60
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament Start Gcode\nM900 K0.033\nSET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 265

[filament:Polymaker_PA12-CF@G-ZERO_0.4]
bed_temperature = 50
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.20mm_PA-CF@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.96
fan_always_on = 1
fan_below_layer_time = 45
filament_abrasive = 1
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 28000
filament_density = 1.04
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "Polymid PA6-CF\n推奨プリント温度 280 – 300 °C\n\nTips\n・本樹脂はESD Safeです。\n・含有する繊維が長いため、0.15㎜以上のレイヤー厚みを推奨します。\n・一層目を観察し、ベッドとノズルの距離を適切に調節しましょう。\n・基礎的な定着力の調整は1番目のレイヤーの温度で調整可能です。\n・印刷物の収縮力が強い場合は2番目以降のレイヤーのベッド温度を上げる。\n・反りが強い場合などにはチャンバーファンを使用し、チャンバー温度を上昇させることができます\n・トップリッドは閉めましょう。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.6
filament_retract_length_toolchange = nil
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "G0_PA12CF_Tentative_2502_V0.3mf (G0_PA12CF_Tentative_2502_V0.3mf (G0_PA12CF_Tentative_2502_V0.3mf (L1_PA12CF_Tentative_20241125.3mf (L1_PA12CF_Tentative_20241125.3mf (dipus_PA6CF_Tentative_20241122.3mf (dipus_PA6CF_Tentative_20241122.3mf (Arm3_PA6CF_Tentative_20240805.3mf (Arm3_PA6CF_Tentative_20240805.3mf (L1_PA6CF_Tentative_20240805.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V3.3mf (NOK_PA6CF_V2.3mf (NOK_PA6CF_V2.3mf (NOK_PA6CF_V1.3mf (NOK_PA6CF_V0.3mf (PA6_L1_V2.3mf (PA6-CF@L1))))))))))))))))))))"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 1
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PA-CF
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = 0
first_layer_bed_temperature = 45
first_layer_temperature = 300
full_fan_speed_layer = 4
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 35
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K0.0275\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1"
temperature = 290

[filament:Polymaker_TPU95-HF@G-ZERO_0.4]
bed_temperature = 30
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = G-ZERO_0.4mmNozzle
compatible_printers_condition = 
compatible_prints = 0.20mm_TPU@G-ZERO_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.98
fan_always_on = 1
fan_below_layer_time = 450
filament_abrasive = 0
filament_colour = #008000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 8000
filament_density = 1.16
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 4
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "生産性と造形安定性の高いPolymaker TPU95-HFです。\nやや硬めですが、インフィルや境界線(シェル)の厚みで柔らかさを調整可能です。\n\n※テクスチャPEIのビルドプレートを推奨します。\n※定着力が強く、スムースPEIのビルドプレートでは造形後に剥がすのが難しくなる場合があります。\n※どうしてもスムースPEIを使用する場合はPVA糊をを塗る等して定着力を弱めてください。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.3
filament_retract_length_toolchange = nil
filament_retract_lift = 0
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker PolyFlex TPU95-HF@G-ZERO"
filament_shrinkage_compensation_xy = 0.7%
filament_shrinkage_compensation_z = 0.18%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 45
first_layer_temperature = 230
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 20
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 45
start_filament_gcode = "; Filament Start Gcode\nM900 K0.12\nSET_PRESSURE_ADVANCE SMOOTH_TIME=0.06\nSET_FAN_SPEED FAN=chamber_fan SPEED=0"
temperature = 210

[filament:Polymaker_TPU95-HF@G-ZERO_L1_0.4]
bed_temperature = 35
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = "G-ZERO_L1_0.40mm Nozzle"
compatible_printers_condition = 
compatible_prints = 0.20mm_TPU@G-ZERO_L1_0.4
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 2
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 180
filament_abrasive = 0
filament_colour = #008000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 8000
filament_density = 1.16
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 4
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = "生産性と造形安定性の高いPolymaker TPU95-HFです。\nやや硬めですが、インフィルや境界線(シェル)の厚みで柔らかさを調整可能です。\n\n※テクスチャPEIのビルドプレートを推奨します。\n※定着力が強く、スムースPEIのビルドプレートでは造形後に剥がすのが難しくなる場合があります。\n※どうしてもスムースPEIを使用する場合はPVA糊をを塗る等して定着力を弱めてください。\n"
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0.3
filament_retract_length_toolchange = nil
filament_retract_lift = 0
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = "Polymaker PolyFlex TPU95-HF@G-ZERO_L1"
filament_shrinkage_compensation_xy = 0.7%
filament_shrinkage_compensation_z = 0.18%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 40
first_layer_temperature = 230
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 90
min_fan_speed = 90
min_print_speed = 15
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 100
overhang_fan_speed_3 = 100
slowdown_below_layer_time = 25
start_filament_gcode = "; Filament Start Gcode\nM900 K0.12\nSET_PRESSURE_ADVANCE SMOOTH_TIME=0.06\n"
temperature = 210

[printer:G-ZERO_0.2mmNozzle]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,250x0,250x200,0x200
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Polymaker PolyLite ASA @G-ZERO"
default_print_profile = 0.05mm ULTRADETAIL @G-ZERO 0.25 nozzle
deretract_speed = 0
end_gcode = ; work around for klipper gcode buffer delay at the end of print\nG91 ; relative\nG0 Z2 F600 ; lift head\nEND_PRINT
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 20000,1250
machine_max_acceleration_retracting = 20000,1250
machine_max_acceleration_travel = 20000,1250
machine_max_acceleration_x = 20000,960
machine_max_acceleration_y = 20000,960
machine_max_acceleration_z = 200,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,100
machine_max_feedrate_y = 500,100
machine_max_feedrate_z = 10,12
machine_max_jerk_e = 4.5,4.5
machine_max_jerk_x = 5,8
machine_max_jerk_y = 5,8
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.1
max_print_height = 201
min_layer_height = 0.04
multimaterial_purging = 140
nozzle_diameter = 0.2
nozzle_high_flow = 0
parking_pos_retraction = 92
pause_print_gcode = M600
prefer_clockwise_movements = 0
print_host = 
printer_model = G-ZERO
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO\n
printer_settings_id = G-ZERO 0.25mm Nozzle
printer_technology = FFF
printer_variant = 0.4
printer_vendor = GUTENBERG
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.2
retract_length_toolchange = 4
retract_lift = 0.1
retract_lift_above = 0
retract_lift_below = 195
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n
template_custom_gcode = 
thumbnails = 32x32/PNG, 400x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:G-ZERO_0.4mmNozzle]
autoemit_temperature_commands = 1
bed_custom_model = C:\\Users\\Yamag\\Downloads\\g-zero_bedmodel_forps.stl
bed_custom_texture = C:\\Users\\Yamag\\Downloads\\g-zero_bedtexturel_forps.svg
bed_shape = 0x0,250x0,250x200,0x200
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Polymaker PolyLite ASA @G-ZERO"
default_print_profile = 0.20 mm TYPICAL @G-ZERO
deretract_speed = 0
end_gcode = END_PRINT
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 20000,1250
machine_max_acceleration_retracting = 20000,1250
machine_max_acceleration_travel = 20000,1250
machine_max_acceleration_x = 20000,960
machine_max_acceleration_y = 20000,960
machine_max_acceleration_z = 200,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,100
machine_max_feedrate_y = 500,100
machine_max_feedrate_z = 10,12
machine_max_jerk_e = 4.5,4.5
machine_max_jerk_x = 5,8
machine_max_jerk_y = 5,8
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.25
max_print_height = 201
min_layer_height = 0.05
multimaterial_purging = 140
nozzle_diameter = 0.4
nozzle_high_flow = 0
parking_pos_retraction = 92
pause_print_gcode = M600
prefer_clockwise_movements = 0
print_host = 
printer_model = G-ZERO
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO\n
printer_settings_id = G-ZERO 0.25mm Nozzle
printer_technology = FFF
printer_variant = 0.4
printer_vendor = GUTENBERG
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.2
retract_length_toolchange = 4
retract_lift = 0.1
retract_lift_above = 0
retract_lift_below = 195
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n
template_custom_gcode = 
thumbnails = 32x32/PNG, 400x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:G-ZERO_L1_0.40mm Nozzle]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,360x0,360x250,0x250
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Polymaker PolyLite ASA @G-ZERO"
default_print_profile = 0.20 mm TYPICAL @G-ZERO
deretract_speed = 0
end_gcode = END_PRINT
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 20000,1250
machine_max_acceleration_retracting = 20000,1250
machine_max_acceleration_travel = 20000,1250
machine_max_acceleration_x = 30000,960
machine_max_acceleration_y = 30000,960
machine_max_acceleration_z = 300,200
machine_max_feedrate_e = 30,120
machine_max_feedrate_x = 700,100
machine_max_feedrate_y = 700,100
machine_max_feedrate_z = 6,12
machine_max_jerk_e = 4.5,4.5
machine_max_jerk_x = 10,8
machine_max_jerk_y = 10,8
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.2
max_print_height = 235
min_layer_height = 0.05
multimaterial_purging = 140
nozzle_diameter = 0.4
nozzle_high_flow = 0
parking_pos_retraction = 92
pause_print_gcode = M600
prefer_clockwise_movements = 0
print_host = 
printer_model = G-ZERO
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO_L1\n
printer_settings_id = G-ZERO_L1 0.40mm Nozzle
printer_technology = FFF
printer_variant = 0.4
printer_vendor = GUTENBERG
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.2
retract_length_toolchange = 4
retract_lift = 0.1
retract_lift_above = 0
retract_lift_below = 230
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n
template_custom_gcode = 
thumbnails = 32x32/PNG, 400x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[presets]
print = 0.10mm_TYPICAL@G-ZERO_0.2
sla_print = 
sla_material = 
printer = G-ZERO_0.2mmNozzle
filament = Polylite_ASA@G-ZERO_0.2