[print:0.05mm ULTRADETAIL @G-ZERO 0.25 nozzle] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 10 bottom_solid_min_thickness = 0.6 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.25mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.26 external_perimeter_speed = 60 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.26 fill_angle = 45 fill_density = 20% fill_pattern = grid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.26 first_layer_height = 0.1 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 12 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.25 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.05 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 0.25mmのノズル用の高精細設定です。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 5000 perimeter_extruder = 1 perimeter_extrusion_width = 0.26 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.05mm ULTRADETAIL @G-ZERO 0.25 nozzle raft_contact_distance = 0.07 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 4 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.26 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.1 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.1 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.22 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.15 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 1.5 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.25 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 15 top_solid_min_thickness = 0.6 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.075mm DETAIL @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 100 bottom_fill_pattern = monotonic bottom_solid_layers = 10 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 60 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 15% fill_pattern = adaptivecubic first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.15 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.42 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.075 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 積層の厚さを細かく刻むことで高さ方向の解像度を高める設定です。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 7500 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.075mm DETAIL @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 4 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 3 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 14 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.10mm DETAIL @G-ZERO 0.25 nozzle] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 7 bottom_solid_min_thickness = 0.6 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.25mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.26 external_perimeter_speed = 60 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.26 fill_angle = 45 fill_density = 20% fill_pattern = grid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.26 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 12 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.25 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.1 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 積層の厚さを細かく刻むことで高さ方向の解像度を高める設定です。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 5000 perimeter_extruder = 1 perimeter_extrusion_width = 0.26 perimeter_generator = arachne perimeter_speed = 150 perimeters = 4 post_process = print_settings_id = 0.10mm DETAIL @G-ZERO 0.25 nozzle raft_contact_distance = 0.07 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 2 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.26 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.1 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.1 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.22 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.15 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 1.5 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.25 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 9 top_solid_min_thickness = 0.6 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.10mm QUALITY @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 100 bottom_fill_pattern = monotonic bottom_solid_layers = 6 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 60 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 15% fill_pattern = gyroid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.42 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.1 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 造形品質を優先する設定です。\n※強度を高める場合はシェル数を増やしてください。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 5000 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.10mm QUALITY @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 4 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 2 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 6 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.10mm STANDARD @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 7 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 100 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 20% fill_pattern = adaptivecubic first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.42 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.1 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = ヘッド駆動速度を活かした標準的な設定です。\n※強度を高める場合はシェル数を増やしてください。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 7500 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.10mm STANDARD @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 2 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 8 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.15mm MODERATE @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 100 bottom_fill_pattern = monotonic bottom_solid_layers = 6 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 100 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 20% fill_pattern = gyroid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.42 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.15 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 造形安定性を重視した中庸なパラメータです。\n※強度を高める場合はシェル数を増やしてください。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 10000 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.15mm MODERATE @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 2 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 6 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.20mm DRAFT @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 4 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 8000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 150 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 15% fill_pattern = adaptivecubic first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 0 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 造形時間の短縮を重視する設定です。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 10000 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 2 post_process = print_settings_id = 0.20mm DRAFT @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 5 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.20mm FLEX @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 100 bottom_fill_pattern = monotonic bottom_solid_layers = 4 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 60 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 20% fill_pattern = gyroid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.5 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 軟質フィラメントを造形する際の設定です。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 7500 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.20mm FLEX @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 5 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [print:0.20mm MODELATE @G-ZERO 0.60 nozzle] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonic bottom_solid_layers = 4 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.60mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.63 external_perimeter_speed = 100 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.63 fill_angle = 45 fill_density = 15% fill_pattern = gyroid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.63 first_layer_height = 0.4 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.6 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 0.6mmノズル用の造形安定性を重視した中庸なパラメータです only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 7500 perimeter_extruder = 1 perimeter_extrusion_width = 0.63 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.20mm MODELATE @G-ZERO 0.60 nozzle raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.63 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.54 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.6 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 5 top_solid_min_thickness = 1.5 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.20mm TYPICAL @G-ZERO] avoid_crossing_curled_overhangs = 1 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 100 bottom_fill_pattern = monotonic bottom_solid_layers = 5 bottom_solid_min_thickness = 0.8 bridge_acceleration = 3000 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 25 brim_separation = 0.1 brim_type = outer_only brim_width = 0 compatible_printers = "G-ZERO 0.40mm Nozzle" compatible_printers_condition = complete_objects = 0 default_acceleration = 10000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.15 enable_dynamic_overhang_speeds = 1 external_perimeter_acceleration = 5000 external_perimeter_extrusion_width = 0.42 external_perimeter_speed = 100 external_perimeters_first = 0 extra_perimeters = 1 extra_perimeters_on_overhangs = 0 extruder_clearance_height = 25 extruder_clearance_radius = 65 extrusion_width = 0.42 fill_angle = 45 fill_density = 20% fill_pattern = gyroid first_layer_acceleration = 3000 first_layer_acceleration_over_raft = 200 first_layer_extrusion_width = 0.42 first_layer_height = 0.2 first_layer_speed = 30 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = 1 gcode_resolution = 0.00442 gcode_substitutions = "G1 F0\\n";"\n";;"G1 F0 エラー回避" infill_acceleration = 15000 infill_anchor = 600% infill_anchor_max = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.42 infill_first = 0 infill_overlap = 10% infill_speed = 300 inherits = interface_shells = 0 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 500 max_volumetric_extrusion_rate_slope_negative = 100 max_volumetric_extrusion_rate_slope_positive = 100 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 10 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 0 notes = 積層を強調したい場合におすすめの設定です。\nCFやGFなどのフィラー入りフィラメントにもおすすめです。\n※強度を高める場合はシェル数を増やしてください。 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_G-ZERO_{print_time}.gcode overhang_speed_0 = 25 overhang_speed_1 = 25 overhang_speed_2 = 30 overhang_speed_3 = 40 overhangs = 1 perimeter_acceleration = 7500 perimeter_extruder = 1 perimeter_extrusion_width = 0.42 perimeter_generator = arachne perimeter_speed = 150 perimeters = 3 post_process = print_settings_id = 0.20mm TYPICAL @G-ZERO raft_contact_distance = 0.1 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 0 skirt_distance = 3 skirt_height = 1 skirts = 2 slice_closing_radius = 0.02 slicing_mode = regular small_perimeter_speed = 60 solid_infill_acceleration = 15000 solid_infill_below_area = 10 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.42 solid_infill_speed = 200 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0.15 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.12 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.36 support_material_interface_contact_loops = 1 support_material_interface_extruder = 0 support_material_interface_layers = 4 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 40 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 200 support_material_style = grid support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 3 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 15% thick_bridges = 0 thin_walls = 1 threads = 8 top_fill_pattern = monotonic top_infill_extrusion_width = 0.4 top_solid_infill_acceleration = 10000 top_solid_infill_speed = 100 top_solid_layers = 5 top_solid_min_thickness = 0.9 travel_acceleration = 15000 travel_speed = 300 travel_speed_z = 4 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 1 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 0 wipe_tower_extra_spacing = 100% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 170 wipe_tower_y = 125 xy_size_compensation = 0 [filament:Carbodeon uDiamond PLA@G-ZERO] bed_temperature = 45 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #FF8000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.24 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 12 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "PLAについて\n・非常に印刷しやすい樹脂です\n\n※ノズル詰まりの危険あり\n　PLAを印刷する際は上蓋を開けることを推奨します。\n" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Carbodeon uDiamond PLA@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PLA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Carbodeon filament_wipe = nil first_layer_bed_temperature = 45 first_layer_temperature = 230 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 100 overhang_fan_speed_3 = 100 slowdown_below_layer_time = 20 start_filament_gcode = "M900 K0.025\nSET_FAN_SPEED FAN=chamber_fan SPEED=0" temperature = 230 [filament:Otsuka Chemical POTICON PA NTL34M@G-ZERO] bed_temperature = 60 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.27 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Otsuka Chemical POTICON PA NTL34M@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Otsuka Chemical filament_wipe = nil first_layer_bed_temperature = 60 first_layer_temperature = 270 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 75 min_fan_speed = 50 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 80 overhang_fan_speed_3 = 80 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 270 [filament:Otsuka Chemical POTICON PA NTL34MB@G-ZERO] bed_temperature = 60 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #9696A0 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.27 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Otsuka Chemical POTICON PA NTL34MB@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Otsuka Chemical filament_wipe = nil first_layer_bed_temperature = 60 first_layer_temperature = 270 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 75 min_fan_speed = 50 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 80 overhang_fan_speed_3 = 80 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 270 [filament:Otsuka Chemical POTICON PA NTL36@G-ZERO] bed_temperature = 60 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.4 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ポリアミドベースのティスモ(チタン酸カリウム)配合フィラメントです。\n高い剛性と強度、耐摩耗性にも優れた素材です。\n\nポリアミドベースの為、造形前の乾燥と造形中の防湿対策を実施してください。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Otsuka Chemical POTICON PA NTL36@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Otsuka Chemical filament_wipe = nil first_layer_bed_temperature = 60 first_layer_temperature = 270 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 75 min_fan_speed = 50 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 80 overhang_fan_speed_3 = 80 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\n;SET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 270 [filament:Otsuka Chemical POTICON PPS RT4@G-ZERO] bed_temperature = 120 bridge_fan_speed = 80 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 15 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.51 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n非常に高い剛性と強度、耐摩耗性、耐薬品性にも優れた素材です。\n\n造形が反ったり強度が出ない場合は、必要に応じてファン速度を0にする、広めのブリムやドラフトシールドを使用するなどしてください。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = 0.1 filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Otsuka Chemical POTICON PPS RT4@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PPS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Otsuka Chemical filament_wipe = nil first_layer_bed_temperature = 120 first_layer_temperature = 340 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 50 min_fan_speed = 30 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 70 overhang_fan_speed_3 = 40 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.008\nSET_FAN_SPEED FAN=chamber_fan SPEED=1\n;SET_TEMPERATURE_FAN_TARGET temperature_fan=Chamber_Intake_Fan target=65\n" temperature = 340 [filament:Otsuka Chemical POTICON PPS RT4E@G-ZERO] bed_temperature = 120 bridge_fan_speed = 80 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 15 filament_colour = #9696A0 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.52 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "PPSベースのティスモ(チタン酸カリウム)配合フィラメントです。\n非常に高い剛性と強度、耐摩耗性、耐薬品性にも優れた素材です。\n本RT4EグレードはESD Safeです。\n\n造形が反ったり強度が出ない場合は、必要に応じてファン速度を0にする、広めのブリムやドラフトシールドを使用するなどしてください。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = 0.1 filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Otsuka Chemical POTICON PPS RT4E@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PPS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Otsuka Chemical filament_wipe = nil first_layer_bed_temperature = 120 first_layer_temperature = 340 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 50 min_fan_speed = 30 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 70 overhang_fan_speed_3 = 40 slowdown_below_layer_time = 5 start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.008\nSET_FAN_SPEED FAN=chamber_fan SPEED=1\n;SET_TEMPERATURE_FAN_TARGET temperature_fan=Chamber_Intake_Fan target=65\n" temperature = 340 [filament:Polymaker PolyCast@G-ZERO] bed_temperature = 45 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #C0C0C0 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.09 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "インベストメント鋳造用の特殊なフィラメントです。\n残留物がなく清潔に焼き尽くされるため、高品質な鋳造原型（ワックス）を造形することができます。\n\n表面加工機「Polysher」を使用すると表面を滑らかに仕上げる事が可能です。" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyCast@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = SPECIAL filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 45 first_layer_temperature = 220 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 100 overhang_fan_speed_3 = 100 slowdown_below_layer_time = 30 start_filament_gcode = "M900 K0.02\nSET_FAN_SPEED FAN=chamber_fan SPEED=0" temperature = 200 [filament:Polymaker PolyFlex TPU90@G-ZERO] bed_temperature = 55 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.04 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 3 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = ショア硬度90Aの軟質フィラメントです。 filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = 0.5 filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyFlex TPU90@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = FLEX filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = 1 first_layer_bed_temperature = 55 first_layer_temperature = 220 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 100 overhang_fan_speed_3 = 100 slowdown_below_layer_time = 15 start_filament_gcode = "; Filament Start Gcode\nM900 K0.00\nSET_FAN_SPEED FAN=chamber_fan SPEED=0.0" temperature = 220 [filament:Polymaker PolyFlex TPU95-HF@G-ZERO] bed_temperature = 35 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #008000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.22 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 5 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "Polymaker TPU95-HFについて\n・高い押し出し速度が特徴で、生産性が高いTPUです。\n・やや硬めですが、インフィルやシェル厚みでも硬さは調整可能です。\n\nTips\n・定着力が強く、ベッドから剥がすのが難しくなる場合があります。端の目立たないところで印刷テストをお勧めします。\n・一層目を観察し、ベッドとノズルの距離を適切に調節しましょう。場合によってはやや遠い程度が良いかもしれません。\n" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = 0.5 filament_retract_length_toolchange = nil filament_retract_lift = 0 filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyFlex TPU95-HF@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = FLEX filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = 1 first_layer_bed_temperature = 35 first_layer_temperature = 220 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 80 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 100 overhang_fan_speed_3 = 100 slowdown_below_layer_time = 15 start_filament_gcode = "M900 K0.05\nSET_FAN_SPEED FAN=chamber_fan SPEED=0" temperature = 220 [filament:Polymaker PolyLite ABS@G-ZERO] bed_temperature = 105 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.04 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ABSについて\n・樹脂としては非常にバランスの取れた性質をしています。\n・やや積層強度を確保するのが難しい面があります。\n\nTips\n・ABSの印刷の際にはフロントドアおよびトップリッドを閉めましょう。\n・一層目を観察し、ベッドとノズルの距離を適切に調節しましょう。\n・基礎的な定着力の調整は1番目のレイヤーの温度で調整可能です。\n・印刷物の収縮力が強い場合は2番目以降のレイヤーのベッド温度を上げる。\n・反りが強い場合などにはチャンバーファンを使用し、チャンバー温度を上昇させることができます。\n・積層強度が不足する場合には冷却風を弱め、印刷速度を落とすことをお勧めします。\n" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyLite ABS@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 110 first_layer_temperature = 260 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 90 overhang_fan_speed_3 = 80 slowdown_below_layer_time = 10 start_filament_gcode = "; Filament Start Gcode\nM900 K0.02\nSET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 255 [filament:Polymaker PolyLite ASA@G-ZERO] bed_temperature = 100 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.04 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 12 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ASAについて\n・ABSのブタジエンゴムをアクリルゴムに変更した樹脂です。対候性や耐酸、耐アルカリ性にも優れます。\n・野外での使用にお勧め\n・収縮は一般的にABSよりやや穏やかです。\n・最大押し出し速度が速いのでABS以上に小型のモックアップの作成に向いています。\n\nTips\n・ABAの印刷の際にはフロントドアおよびトップリッドを閉めましょう。\n・一層目を観察し、ベッドとノズルの距離を適切に調節しましょう。\n・基礎的な定着力の調整は1番目のレイヤーの温度で調整可能です。\n・印刷物の収縮力が強い場合は2番目以降のレイヤーのベッド温度を上げる。\n・反りが強い場合などにはチャンバーファンを使用し、チャンバー温度を上昇させることができます。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyLite ASA@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = ASA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 100 first_layer_temperature = 260 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 75 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 90 overhang_fan_speed_3 = 80 slowdown_below_layer_time = 10 start_filament_gcode = "; Filament Start Gcode\nM900 K0.015\nSET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 255 [filament:Polymaker PolyLite PC@G-ZERO] bed_temperature = 105 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 15 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.04 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "扱いやすいポリカーボネート材料です。\n押し出し体積速度は低めで、高速造形にはやや不向きです。" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = 0.3 filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker Polylite PC@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PC filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 105 first_layer_temperature = 270 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 60 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 70 overhang_fan_speed_3 = 40 slowdown_below_layer_time = 15 start_filament_gcode = "; Filament Start Gcode\nM900 K0.028\nSET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 270 [filament:Polymaker PolyLite PETG@G-ZERO] bed_temperature = 80 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 1 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 20 filament_colour = #FF8000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.27 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "ノズルが詰まる場合がありますので印刷する際は上蓋を開けることを推奨します" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = 0.3 filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PolyLite PETG@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PETG filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = 1 first_layer_bed_temperature = 80 first_layer_temperature = 240 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 70 overhang_fan_speed_3 = 40 slowdown_below_layer_time = 15 start_filament_gcode = "M900 K0.012\nSET_FAN_SPEED FAN=chamber_fan SPEED=0" temperature = 240 [filament:Polymaker PolyLite PLA@G-ZERO] bed_temperature = 45 bridge_fan_speed = 100 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FF8000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.24 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "PLAについて\n・一般的には収縮が小さく印刷しやすい樹脂です。\n・造形後は他の樹脂に比べて硬めです。\n・一方で耐衝撃性は高くありません。\n・軟化温度は50～60℃程度で耐熱性は高くありません。\n・G-ZEROの場合は上蓋を開けて造形してください。\n・庫内温度の上昇しすぎると造形トラブルになる場合があります。\n\n\n※ノズル詰まりの危険あり\n　PLAを印刷する際は上蓋を開けることを強く推奨します。\n" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker Polylite PLA@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PLA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 45 first_layer_temperature = 220 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 15 overhang_fan_speed_0 = 100 overhang_fan_speed_1 = 100 overhang_fan_speed_2 = 100 overhang_fan_speed_3 = 100 slowdown_below_layer_time = 30 start_filament_gcode = "M900 K0.02\nSET_FAN_SPEED FAN=chamber_fan SPEED=0" temperature = 220 [filament:Polymaker PolyMide PA6-CF@G-ZERO] bed_temperature = 65 bridge_fan_speed = 75 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 30 filament_colour = #FFF2EC filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 0 filament_density = 1.04 filament_deretract_speed = nil filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 12 filament_minimal_purge_on_wipe_tower = 15 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "Polymid PA6-CF\n推奨プリント温度 280 – 300 °C\n\nTips\n・本樹脂はESD Safeです。\n・含有する繊維が長いため、0.15㎜以上のレイヤー厚みを推奨します。\n・一層目を観察し、ベッドとノズルの距離を適切に調節しましょう。\n・基礎的な定着力の調整は1番目のレイヤーの温度で調整可能です。\n・反りが強い場合などにはベッド温度を50度以下に下げることで、反りを抑えられる場合があります\n・トップリッドは閉めましょう。\n" filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = 0.4 filament_retract_length_toolchange = nil filament_retract_lift = 0 filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_settings_id = "Polymaker PA6-CF@G-ZERO" filament_soluble = 0 filament_spool_weight = 0 filament_toolchange_delay = 0 filament_type = PA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 filament_vendor = Polymaker filament_wipe = nil first_layer_bed_temperature = 65 first_layer_temperature = 300 full_fan_speed_layer = 0 idle_temperature = nil inherits = max_fan_speed = 75 min_fan_speed = 40 min_print_speed = 15 overhang_fan_speed_0 = 75 overhang_fan_speed_1 = 75 overhang_fan_speed_2 = 75 overhang_fan_speed_3 = 60 slowdown_below_layer_time = 5 start_filament_gcode = "M900 K0.015\nSET_FAN_SPEED FAN=chamber_fan SPEED=1" temperature = 300 [printer:G-ZERO 0.25mm Nozzle] autoemit_temperature_commands = 1 bed_custom_model = bed_custom_texture = bed_shape = 0x0,250x0,250x200,0x200 before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n between_objects_gcode = color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = "Polymaker PolyLite ASA @G-ZERO" default_print_profile = 0.05mm ULTRADETAIL @G-ZERO 0.25 nozzle deretract_speed = 0 end_gcode = ; work around for klipper gcode buffer delay at the end of print\nG91 ; relative\nG0 Z2 F600 ; lift head\nEND_PRINT extra_loading_move = -2 extruder_colour = "" extruder_offset = 0x0 gcode_flavor = marlin high_current_on_filament_swap = 0 host_type = octoprint inherits = layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00 machine_limits_usage = time_estimate_only machine_max_acceleration_e = 5000,5000 machine_max_acceleration_extruding = 20000,1250 machine_max_acceleration_retracting = 20000,1250 machine_max_acceleration_travel = 20000,1250 machine_max_acceleration_x = 20000,960 machine_max_acceleration_y = 20000,960 machine_max_acceleration_z = 200,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,100 machine_max_feedrate_y = 500,100 machine_max_feedrate_z = 10,12 machine_max_jerk_e = 4.5,4.5 machine_max_jerk_x = 5,8 machine_max_jerk_y = 5,8 machine_max_jerk_z = 0.4,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.18 max_print_height = 201 min_layer_height = 0.07 nozzle_diameter = 0.25 parking_pos_retraction = 92 pause_print_gcode = M600 print_host = printer_model = G-ZERO printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO\n printer_settings_id = G-ZERO 0.25mm Nozzle printer_technology = FFF printer_variant = 0.4 printer_vendor = GUTENBERG printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 2 retract_before_wipe = 0% retract_layer_change = 1 retract_length = 0.2 retract_length_toolchange = 4 retract_lift = 0.1 retract_lift_above = 0 retract_lift_below = 195 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 silent_mode = 0 single_extruder_multi_material = 0 start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n template_custom_gcode = thumbnails = 32x32,400x300 thumbnails_format = PNG toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:G-ZERO 0.40mm Nozzle] autoemit_temperature_commands = 1 bed_custom_model = bed_custom_texture = bed_shape = 0x0,250x0,250x200,0x200 before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n between_objects_gcode = color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = "Polymaker PolyLite ASA @G-ZERO" default_print_profile = 0.20 mm TYPICAL @G-ZERO deretract_speed = 0 end_gcode = END_PRINT extra_loading_move = -2 extruder_colour = "" extruder_offset = 0x0 gcode_flavor = marlin high_current_on_filament_swap = 0 host_type = octoprint inherits = layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00 machine_limits_usage = time_estimate_only machine_max_acceleration_e = 5000,5000 machine_max_acceleration_extruding = 20000,1250 machine_max_acceleration_retracting = 20000,1250 machine_max_acceleration_travel = 20000,1250 machine_max_acceleration_x = 20000,960 machine_max_acceleration_y = 20000,960 machine_max_acceleration_z = 200,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,100 machine_max_feedrate_y = 500,100 machine_max_feedrate_z = 10,12 machine_max_jerk_e = 4.5,4.5 machine_max_jerk_x = 5,8 machine_max_jerk_y = 5,8 machine_max_jerk_z = 0.4,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.25 max_print_height = 201 min_layer_height = 0.05 nozzle_diameter = 0.4 parking_pos_retraction = 92 pause_print_gcode = M600 print_host = printer_model = G-ZERO printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO\n printer_settings_id = G-ZERO 0.25mm Nozzle printer_technology = FFF printer_variant = 0.4 printer_vendor = GUTENBERG printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 2 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 0.2 retract_length_toolchange = 4 retract_lift = 0.1 retract_lift_above = 0 retract_lift_below = 195 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 silent_mode = 0 single_extruder_multi_material = 0 start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n template_custom_gcode = thumbnails = 32x32,400x300 thumbnails_format = PNG toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0 [printer:G-ZERO 0.60mm Nozzle] autoemit_temperature_commands = 1 bed_custom_model = bed_custom_texture = bed_shape = 0x0,250x0,250x200,0x200 before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0.0\n;[layer_z]\n\n between_objects_gcode = color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = "Polymaker PolyLite ASA @G-ZERO" default_print_profile = 0.20mm MODELATE @G-ZERO 0.60 nozzle deretract_speed = 0 end_gcode = END_PRINT extra_loading_move = -2 extruder_colour = "" extruder_offset = 0x0 gcode_flavor = marlin high_current_on_filament_swap = 0 host_type = octoprint inherits = layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nDISPLAY_GCODE_PROGRESS TOTAL_LAYER=[total_layer_count] CURRENT_LAYER={layer_num+1} PROGRESS=0 REMAIN=00:00 machine_limits_usage = time_estimate_only machine_max_acceleration_e = 5000,5000 machine_max_acceleration_extruding = 20000,1250 machine_max_acceleration_retracting = 20000,1250 machine_max_acceleration_travel = 20000,1250 machine_max_acceleration_x = 20000,960 machine_max_acceleration_y = 20000,960 machine_max_acceleration_z = 200,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,100 machine_max_feedrate_y = 500,100 machine_max_feedrate_z = 10,12 machine_max_jerk_e = 4.5,4.5 machine_max_jerk_x = 5,8 machine_max_jerk_y = 5,8 machine_max_jerk_z = 0.4,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.45 max_print_height = 201 min_layer_height = 0.15 nozzle_diameter = 0.6 parking_pos_retraction = 92 pause_print_gcode = M600 print_host = printer_model = G-ZERO printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_GUTENBERG\nPRINTER_MODEL_G-ZERO\n printer_settings_id = G-ZERO 0.60mm Nozzle printer_technology = FFF printer_variant = 0.4 printer_vendor = GUTENBERG printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 2 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 0.25 retract_length_toolchange = 4 retract_lift = 0.15 retract_lift_above = 0 retract_lift_below = 195 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 silent_mode = 0 single_extruder_multi_material = 0 start_gcode = M140 S0\nM104 S0\nSTART_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature] AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} FILAMENT_TYPE={filament_type[0]}\n\n template_custom_gcode = thumbnails = 32x32,400x300 thumbnails_format = PNG toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0 [presets] print = 0.20mm DRAFT(PS260) @G-ZERO sla_print = - default - sla_material = - default - printer = G-ZERO 0.40mm Nozzle(PS260) filament = Polymaker Polylite ASA(PS260) @G-ZERO